product name

Troy-Bilt 21AE654K766 7hp Roto-Tiller (2004)

Model: 21AE654K766 7HP Roto-Tiller (2004)

Back To Assemblies

Save
 Part Not Listed?Part Not Listed?
product name

Transmission

...
...
1
Shaft Assembly, Detent MTD-611-04033
...
2
Housing, Transmission MTD-619-04069
...
3
Cover, Housing, Transmission MTD-619-04070
...
4
Link Assembly, Shift MTD-686-04046
...
5
Hex Screw, 5/16-18,.75, Gr5, Patch If loosened or removed, a sealant (Loctite Ultra Black(TM) Silicone 5900) must be applied to these screws before they can be reused without risking the loss of transmission oil. MTD-710-1880
...
6
Screw, Machine, #10-24, 0.625 MTD-710-0425
...
7
Hex Screw, 1/4-20,.75, Gr5 If loosened or removed, a sealant (Loctite Ultra Black(TM) Silicone 5900) must be applied to these screws before they can be reused without risking the loss of transmission oil. MTD-710-3015
...
8
Flange Screw, 5/16-18,.625, Gr5 MTD-710-04049
...
9
Flange Screw, 5/16-18, 1.0, Gr5 If loosened or removed, a sealant (Loctite Ultra Black(TM) Silicone 5900) must be applied to these screws before they can be reused without risking the loss of transmission oil. MTD-710-04048
...
10
Shaft, Wheel,.750 Dia x 15.46 Lg MTD-711-04261
...
11
Shaft, Tiller, Tine MTD-711-04263
...
12
Shaft, Worm, Drive MTD-711-04178
...
13
Shaft, Idler,.500 Dia x 1.823 Lg MTD-711-04177
...
14
Shaft, Drive MTD-711-04168
...
15
Nut, Hex Lock, #10-24, Gr2, Nylon MTD-712-0161
...
16
Dowel Pin MTD-915-0221
...
17
Ring, Retaining, External, 1.188 Dia Shaft MTD-716-04026
...
18
Ring, Retaining, Int, 1.25 Dia Bore MTD-716-04027
...
19
Ring, Snap,.500 MTD-716-0865
...
20
Gear, Spur, 30t MTD-717-04088
...
21
Gear, Spur, 34t MTD-717-04084
...
22
Gear, Spur, 10t MTD-717-04083
...
23
Gear, Spur, 13t MTD-717-04087
...
24
Gear, Worm, 30t MTD-717-04093
...
25
Gear, Worm, 40t MTD-717-04090
...
26
Collar, Clutch MTD-718-04074
...
27
Cover, Bearing, Rear MTD-718-04065
...
28
Bearing Cover MTD-918-04435
...
30
Oil Seal x.375 MTD-721-0212
...
31
Seal, Oil,.750 Shaft x 1.125 Bore MTD-721-04073
...
33
O-Ring, 1/4 x 3/8 x.07 MTD-721-04069
...
34
Seal,.750 Shaft x1.783 Bore x.375 MTD-721-04065
...
35
Seal,.563 Shaft x 1.25 Bore x.25 MTD-721-04064
...
36
Seal,Oil 1.00 Shft X 1.500 Bore MTD-921-04036
...
37
Washer, Flat,.751 x.975 x.01 MTD-736-04153
...
38
LOCK WASHER 5/16 MTD-936-0119
...
39
THRUST WASHER Shims used "As Required" to obtain between .005" and .015" allowable end-play MTD-936-0492
...
40
Thrust Wash. .621" I.D. x 1.12" MTD-936-0419
...
41
Flat Washer, .344 x .750 x .120 These washers are found only on replacement transmissions. Remove and discard the washers when mounting the transmission to the tiller's tine shield bracket. MTD-936-3008
...
42
Washer, Flat,.5685 x.875 x.04 MTD-736-04102
...
43
THRUST WASHER MTD-736-0495
...
44
Washer, Thrust,.750 x 1.250 x.0615 MTD-736-0617
...
45
Grease, Seal MTD-737-0356
...
46
Oil, 85w 140 MTD-737-0353
...
47
Bearing, Hub MTD-741-04077
...
48
Bearing, 9/16 x 1.25 x.650 Lg MTD-741-04075
...
49
Bearing, Sleeve,.627 x.81 x.80 MTD-741-0973
...
50
Flange Bearing, 5/8 x 3/4 x 3/4 MTD-941-0336
...
51
Bearing, Sleeve,.503 x.626 x.600 MTD-741-0678
...
52
Bearing, Thrust, Roller.625x1.125x.078 MTD-741-0469
...
53
SLEEVE BEARING .75X1.00X1.00 MTD-741-05060
...
54
Retaining Ring MTD-716-04104
...
55
Rear Cover, Transmission MTD-1916109001
...
56
Bushing, 1.25 x 1 x .005 x 1.5 MTD-941-04300
...
57
Flat Washer, 1/234 x 1.015 x .062 MTD-736-04310
...
58
Washer, Flat, 1.015 x 1.234 x.010 Shims used "As Required" to obtain between .005" and .015" allowable end-play MTD-GW-1132-3
...
59
Washer, 1.375 x 1.015 x .062 Shims used "As Required" to obtain between .005" and .015" allowable end-play MTD-736-04309
...
60
Washer, 1.375 x 1.015 x .03 Shims used "As Required" to obtain between .005" and .015" allowable end-play MTD-736-04260
...
61
Washer, 1.375 x 1.015 x .015 Shims used "As Required" to obtain between .005" and .015" allowable end-play MTD-736-04259
...
62
Washer, 1.375 x 1.015 x .01 Shims used "As Required" to obtain between .005" and .015" allowable end-play MTD-736-04258
...
63
Flat Washer, 1.375 x 1.015 x .005 Shims used "As Required" to obtain between .005" and .015" allowable end-play MTD-736-04257
...
64
Washer, Flat, 1.50 x 1.75 x .010 Shims used "As Required" to obtain between .005" and .015" allowable end-play MTD-736-04308
...
65
Washer, Flat, 1.50 x 1.75 x .03 Shims used "As Required" to obtain between .005" and .015" allowable end-play MTD-736-04307
...
66
Washer, Flat, 1.50 x 1.75 x .005 Shims used "As Required" to obtain between .005" and .015" allowable end-play MTD-736-04306
...
67
Washer, Flat, 1.50 x 1.75 x .062 Shims used "As Required" to obtain between .005" and .015" allowable end-play MTD-736-04305
...
68
Gear Housing Gasket MTD-921-04229
...
69
Cup Bearing MTD-941-04299
...
70
Cone Bearing MTD-941-04298
...
71
Retaining Ring, Int MTD-716-04102
...
72
Pipe Plug MTD-737-04202
...
...
...
Processing